QSahara
Q Sahara has no threshold to set. You drive INPUT into a fixed internal threshold and the compressor reacts to the material, much like a classic analog unit. ATTACK and RELEASE lean it faster or slower instead of counting milliseconds, and RATIO hardens the knee as it adds control. Compression, and only compression, for decisions made by ear.
Like its namesake, Sahara shapes the landscape it touches, smoothing peaks, connecting phrases, and bringing flow and continuity to your sound.Ziad Sidawi, from the preface
Set four habits aside
Sahara does not behave like a conventional compressor. The User Guide opens with these four points, and they explain most of what follows.
From IN to OUT
Q Sahara is a feed-forward compressor: the detector reads the input before gain reduction happens, for a precise, controlled response. The meter points sit where the boxes show them.
Five minutes with Q Sahara
Point at any control
Every control, one line each
Names as printed on the panel. With Show Labels on (Settings menu), the controls show their values.
| Control | Range | What it does |
|---|---|---|
| Drive and level | ||
| INPUT | −24 to +24 dB | How hard the signal hits the fixed internal threshold: a drive control, not a trim. Up for more compression, down for less. |
| OUTPUT | −24 to +24 dB | Compensates the level change of compression. MATCH writes its result here when you switch it off. A manual gain stage, not a ceiling. |
| MATCH | Off · On | Holds the output at the loudness of the incoming signal while you dial in; switched off, its compensation stays in OUTPUT. |
| Dynamics | ||
| RATIO | 1.5 · 2.5 · 4 · 7 · 10 · 20 · 40 | Strength and knee hardness together. Lower ratios are softer and more forgiving, higher ones tighten control and harden the knee. Not a true limiter, even at 40. |
| ATTACK | FAST −100 · 0 · +100 SLOW | When compression engages. Negative: sooner, a tighter entry. 0: neutral. Positive: later, more of the initial transient through. |
| RELEASE | FAST −100 · 0 · +100 SLOW | How quickly compression lets go. Negative: quick recovery between hits, denser. Positive: a gradual release that keeps space and groove; large positive values are normal on acoustic and bus material. |
| Detector | ||
| SC HP | OFF · 10 · 20 · 30 · 50 · 70 · 80 · 130 · 220 · 350 Hz | A stepped high-pass on what the detector hears; the audio is not filtered. Keeps low end from triggering needless gain reduction: preserves punch, prevents pumping. |
| SC | Off · On | External sidechain: another source feeds the detector. It only triggers compression and is never heard; the routing is set up in your DAW. |
| LINK | 0 to 100 (100 by default) | How much gain reduction left and right share. 100: both channels compress together, a solid image. Lower: more independent channels, more side-to-side life. |
| Weight and blend | ||
| HAMMER | Off · On | The weight switch. Off: lean and warm. On: Sahara leans in, with low weight that blooms with the bass, a firmer grab on top and a touch of gloss. |
| MIX | 0 to 100 %D (WET to DRY) | Blends the dry signal into the compressed signal; the readout shows the dry share. 0 % D is the processed signal alone. |
| Quality and safety | ||
| ECO · HD | ECO (default) · HD | Oversampling quality; oversampling itself is always on. HD glows amber. |
| Ø | Off · On | Inverts the output, wet and dry together, click-free: to check or correct polarity against a parallel chain or a second microphone. |
| BYPASS | Active · Bypassed | The power switch on the center emblem glows while Sahara is active. Bypass crossfades over 20 ms and stays delay-compensated. |
Judge compression, not volume
MATCH holds the output at the loudness of the incoming signal. Engage it while audio plays: the button pulses while it is actively measuring. Give it a few seconds to settle, then shape the compression freely.
Shift-linked drive is not MATCH. Holding Shift while you drag INPUT moves OUTPUT the opposite way by equal amounts: a quick first approximation that does not measure loudness. For measured matching, use MATCH.
Reading the meters
The metering makes gain staging and compression visible at a glance: the raw input, what INPUT sends on, the output and the gain reduction. Point at a number to find it on the panel.
- 1GR LEDs. Ten segments show gain reduction, how much the compressor turns the signal down, with more room for the 0 to 6 dB range.
- 2GR readout. The current gain reduction in dB; it briefly holds peak values before returning to real-time tracking.
- 3Black needle. The raw input signal, RMS: the level before INPUT.
- 4Red needle. The output signal, RMS.
- 5Curved white meter (RAW+IN on the dial): the raw input plus the gain of INPUT, what actually drives the compressor.
- 6Peak bars. The thin bars at the left and right edges of the glass show the real-time peak level of IN and OUT.
- 7Peak readouts. In dBFS at the top of each bar; they turn red above −3 dBFS.
- 8RMS readouts. Under the IN and OUT labels.
Gain reduction in your host and on hardware
Q Sahara reports its gain reduction to compatible VST3 hosts and hardware controllers. The reported value follows the ballistics of Sahara’s own GR meter, so external meters move exactly as the display does, and it reads 0 dB while the plug-in is bypassed.
HAMMER, LINK, ECO and HD
HAMMER
HAMMER is the weight switch of Q Sahara. Off, the bottom end is lean and warm: a subtle, always-on low-frequency stage keeps it alive without adding weight.
On, Sahara leans in as one gesture: a standing foundation lifts the sub around 25 Hz and the low-mid body around 200 Hz, the sub blooms harder with the bass content of the incoming audio rather than boosting statically, the compressor grabs the top a little firmer, and a touch of gloss rides up top so the balance never tips dark. Because the bloom follows the level, the low end speaks when the material hits and stays controlled when it does not. Switch HAMMER on when you want Sahara to hit harder.
Stereo LINK
The LINK slider in the lower bar sets how much gain reduction the left and right channels share. 100 is the default.
Low-frequency detection always works from the mono sum of both channels, so the low end stays anchored at any LINK setting. When the channels diverge, the GR meter shows the deeper of the two.
Oversampling: ECO and HD
Oversampling covers the whole signal path, the detector included, and is always engaged: there is no off position. It improves low-end definition and reduces intermodulation artifacts under heavy compression. The selector at the top left picks the quality.
| Mode | 44.1 · 48 kHz | 88.2 · 96 kHz | 176.4 · 192 kHz |
|---|---|---|---|
| ECO | 4X | 2X | 2X |
| HD | 8X | 4X | 2X |
Switching between ECO and HD takes effect with a brief, click-free blink: the audio dips for a few milliseconds while the engine reconfigures, and the selector fades with it. The reported latency is identical in both modes, so the switch never disturbs the delay compensation of your DAW.
Bypass, polarity and the external sidechain
If this, then that
| If | Do this |
|---|---|
| Gain reduction the moment Sahara is inserted | Expected: the threshold is fixed. Lower INPUT to reduce compression. |
| A preset sounds louder or quieter than bypass | Engage MATCH briefly and switch it off, or trim OUTPUT. Change INPUT only if you also want different compression. |
| Low end makes the compressor pump | Raise SC HP. |
| You want more of the initial transient through | Move ATTACK toward positive, and judge by ear. |
| You want an earlier grab and a tighter entry | Move ATTACK toward negative. |
| Tails feel cut short, air is lost | Move RELEASE toward positive. |
| Compression feels loose, tails ring on | Move RELEASE toward negative. |
| You need density and control without limiting artifacts | Raise RATIO: the knee hardens, and Sahara still will not brickwall. |
| A parallel blend loses punch or low end | Give MIX more dry signal. |
| The bottom end is lean, or heavy and thick | Lean: switch HAMMER on. Heavy or thick: switch it off. |
| Wide material loses side-to-side life, or the image wanders | Losing life: lower LINK below 100. Wandering: return LINK to 100. |
| Sahara feels less precise or punchy than expected | Set the oversampling selector to HD. |
| A setting is hard to judge without loudness bias | Engage MATCH while you dial in, then switch it off: the compensation is written into OUTPUT. |
| CPU load is high in a large session | Set the oversampling selector to ECO. |
Deeper uses
Presets and the browser
Sahara presets are starting points, not static solutions. Each establishes a character and a calibration between INPUT and OUTPUT; from there, drive INPUT to taste and let the program-dependent timing follow the material.
Click the preset name at the top of the plug-in to open the browser; the arrows beside the name step through presets without opening it. Point at any part of the browser below.
Backing up presets
Presets are files: copy them anywhere to back them up.
C:\Users\Public\Documents\Pulsar Modular\Q Sahara\Presets/Users/Shared/Pulsar Modular/Q Sahara/Presets~/.local/share/Pulsar Modular/Q Sahara/PresetsPro Tools
Pro Tools handles plug-in presets its own way. Set these two options in the Preset menu in the header bar of the plug-in window, and Pro Tools recalls your latest settings and keeps them with the session, alongside the browser of Sahara.
The factory library
129 factory presets and the Default, in the folders the browser shows. Search by name, folder or #tag to find a starting point for your source.
Show all 129 factory presets
- 2Bus Body Wide
- 2Bus Body
- 2Bus Comp
- 2Bus Full
- 2Bus NY Comp
- Bus Hammer Weight
- Warm Breeze
- Wide Bus Breathe
- BV_Ac GTR Arpeggios
- BV_El Bass
- BV_LoFi Shaker Wash
- BV_Longer Snare Bott
- BV_Parallel Drums
- BV_Snappy Snare
- ML_AC Bass
- ML_AC Guitar
- ML_Bass 2
- ML_Bass 3
- ML_Bass
- ML_DR Bus
- ML_Guitar Glue
- ML_Kick Punch
- ML_Kybd
- ML_OH
- ML_Punchy Snare
- ML_Stereo Bus
- ML_Vocal
- Bass Control
- Bass Grit
- Bass Hammer Deep
- Bass Hold
- Bass Old School
- Bass Parallel Weight
- Bass Power
- Bass Transient
- Aura
- Crush
- Duck to Kick
- EL Pancho
- FX Pump
- FX Smash Parallel
- Grit 200
- Grit 500
- Hold On
- NY Comp
- Parallel Smash
- Perc Tight
- Perc Upfront
- Smack That B
- Smack
- Drum Bus- Glue
- Drum Kit Transients
- Drum Upfront
- Drums OH
- Drumzilla
- Hand Claps
- Hand Drum
- Tambourine
- Kick Click
- Kick Round
- Kick Solid
- Punch Parallel
- Sub Control
- Tight Modern
- Vintage Fat
- Body & Tone
- Fast Articulation
- Natural Control
- Parallel Lift
- Transient Focus
- Body
- Parallel Crush
- Snare Blend
- Snare Brush Punch
- Snare Rattle
- Snare Snap
- Tight
- Vintage Round
- Natural Control
- Punch & Focus
- Upfront Parallel
- Vintage Round
- Body
- Natural
- Parallel Lift
- Pick Control
- Strum Glue
- Clean Sustain
- GTR Fuzz
- GTR Shine
- Guitar Grab
- Parallel Thickness
- Rhythm Glue
- Keys 2
- Keys Parallel Lift
- Keys Presence
- Keys Tight
- Keys Transient Focus
- Keys
- Organ
- Piano Rock
- Pad Glue
- Pad Movement
- Pad Parallel Width
- Pad Slow Hold
- Synth Control
- Synth Drive
- Synth Parallel Push
- Synth Rhythm
- Ensemble Body
- Ensemble Glue
- Ensemble Parallel Lift
- Strings Crunch
- Strings Rev
- Solo Bow Control
- Solo Natural
- Solo Sustain
- Violins Tight
- Vocal Fast Control
- Vocal Hold
- Vocal Intimate
- Vocal Leveler- Presence
- Vocal Leveler- Warm
- Vocal Magnum
- Vocal Natural
- Vocal Parallel Lift
- Vocal Presence
- Vocal Smooth Top
- Vocal Upfront
Conventions across the panel
| Gesture | Result |
|---|---|
| Shift + drag INPUT or OUTPUT | Moves the other knob the opposite way by the same amount, so drive changes stay level-matched. A mouse gesture: it does not act on automation playback. |
| Click the A | B area | Switches between the two comparison slots. |
| Click the arrow button | Copies the active slot onto the other one. |
| Click the preset name | Opens the preset browser; the arrows beside it step through presets. |
| Click the help strip | Switches the help on or off; switched off, the strip disappears entirely. Show Tooltips in the menu does the same. |
| Drag the corner at the bottom right | Resizes the window. The size is saved with the session; Set Default Size in the menu makes it the default for new instances. |
| Show Labels in the menu | Shows or hides the numeric value readouts on the controls. |
| Point at a control | The help strip describes it, with the current value. |
Coming from version 1
Version 2 refines the voice of Sahara rather than adding complexity.
Linux notes
On Linux Q Sahara installs as VST3 and LV2, from a .deb package or a .tar.gz archive.
| Harrison Mixbus | Prefer the LV2 build: the libraries Mixbus bundles can conflict with the VST3 interface. |
| Window sizing | The LV2 window is resized by dragging its frame edges, down to half the design size; in REAPER it also has a corner handle. A frame wider or taller than the panel keeps the shape of the panel and centers it. The corner handle and Window Size in the menu apply to the VST3 build; in Ardour and Mixbus the VST3 window follows the corner handle both ways. There the LV2 window does not grow by itself when the browser opens: drag the frame wider for a larger browser. |
| Control surfaces | Hosts read the parameters of the LV2 build as plain numbers (RATIO as steps 0 to 6, for example): LV2 cannot supply formatted readouts such as 40:1. The VST3 build reports formatted values, and gain reduction too. |
| REAPER | Use the VST3 build: REAPER cannot automate the LV2 parameters of JUCE-based plug-ins. |
| License | One activation covers both formats in every host, for your user account on this computer. It is tied to this Linux installation (/etc/machine-id): reinstalling or cloning the system counts as a new computer, so deactivate first in License Status. The license is stored in ~/.config/Pulsar Modular/Licensing, shared by all Pulsar Modular plug-ins. |
| Files | Presets and user guides: ~/.local/share/Pulsar Modular/Q Sahara. Settings: ~/.config/Pulsar Modular/Q Sahara. |
| Audio dropouts | Crackles at small buffer sizes usually mean missing realtime privileges: add your user to the audio group with realtime limits, as the audio documentation of your distribution describes, and log in again. On laptops, also switch to the performance power profile. |
sudo dpkg-reconfigure q-sahara
On iPad and iPhone
Q Sahara for iOS is an AUv3 plug-in and a standalone app for iPad and iPhone (iOS 15 or later), from the App Store. The panel is the same; these are the differences.
| Touch | Drag a knob or slider up or down to change it, and tap wherever the desktop takes a click. With Show Labels on, touching a control shows its value under it; tap the value to type a new one on the numbers keyboard. The help strip describes the control your finger rests on. |
| Link Input & Output | iOS has no Shift key, so the Shift-linked drive lives in the Settings menu: switch on Link Input & Output, and dragging either knob moves the other the opposite way until you switch it off. The switch is kept on the device, for the app and the plug-in alike. |
| Settings menu | No License Status and no Set Default Size: the App Store handles installation and licensing, and the interface scales itself to the screen or the plug-in window of the host. Under Manuals, the Quick Guides and User Guides open on pulsarmodular.com; inside a host the plug-in cannot open a browser, so it copies the link for you to paste into one. |
| Screen | Upright, the panel fills the screen; sideways, it sits in the middle. The open preset browser is shown on its own, as large as the screen allows; tap outside it to close it. |
| Preset browser | Tap a preset to load it; double-tap loads it and closes the browser. Touch and hold a preset or a folder for the menu a right-click opens on the desktop. A finger drag only scrolls the lists, so move presets and folders with Move to folder… in that menu. Delete removes a preset for good: iOS has no Trash. Export shares a preset as a file, and Import adds presets from the Files app. |
| Presets | The app and the AUv3 plug-in share one preset library, stored inside the app’s container and included in device backups. It does not show in the Files app, and deleting the app deletes your user presets with it. An update replaces only the factory presets you have not changed; a factory preset you edited, moved or deleted stays as you left it, and the Default preset is never replaced. |
| ECO and HD | ECO, the default, suits mobile CPU and battery budgets. HD is available from the selector at any time and behaves exactly as on the desktop. |
| Standalone app | It starts with its audio input muted to avoid feedback; tap Unmute Input once headphones or an audio interface are connected. |
| Hosts and metering | The AUv3 plug-in runs in AUM, GarageBand, Logic Pro for iPad, Cubasis, Loopy Pro and other AUv3 hosts. Gain-reduction reporting to hosts and controllers belongs to the desktop VST3 and AAX formats and is not available in AUv3. |
Removing Q Sahara
C:\Program Files\Common Files\VST3\Pulsar Modular\Q Sahara.vst3C:\Program Files\Common Files\Avid\Audio\Plug-Ins\Pulsar Modular\Q Sahara.aaxpluginC:\Users\Public\Documents\Pulsar Modular\Q Sahara/Library/Audio/Plug-Ins/Components/Q Sahara.component/Library/Audio/Plug-Ins/VST3/Pulsar Modular/Q Sahara.vst3/Library/Application Support/Avid/Audio/Plug-Ins/Pulsar Modular/Q Sahara.aaxplugin/Users/Shared/Pulsar Modular/Q Sahara/usr/lib/lv2 and the VST3 link from the ~/.vst3 of each user.sudo apt remove q-sahara
./uninstall.sh in the folder you unpacked it into, or delete:~/.vst3/Q Sahara.vst3~/.lv2/Q Sahara.lv2~/.config/Pulsar Modular (settings) and ~/.local/share/Pulsar Modular (user guide and presets). The Licensing folder next to them holds the licenses of all Pulsar Modular plug-ins on the computer.On Windows and macOS, if no other folders remain under Pulsar Modular in the shared folder, you can delete that folder as well.
Specifications
| Type | Input-driven channel compressor, feed-forward, with a fixed internal threshold and program-dependent attack and release |
| Controls | INPUT and OUTPUT ±24 dB · RATIO 1.5 to 40:1 in seven steps · ATTACK and RELEASE −100 to +100 · MIX 0 to 100 %D · SC HP off or 10 to 350 Hz in nine steps · LINK 0 to 100 |
| Switches | MATCH · HAMMER · ECO / HD · polarity Ø · external sidechain · bypass · A | B |
| Oversampling | Always on, for the whole path including the detector. ECO (default): 4X at 44.1 and 48 kHz, 2X at higher rates. HD: 8X at 44.1 and 48 kHz, 4X at 88.2 and 96 kHz, 2X at 176.4 and 192 kHz |
| Latency | Identical in ECO and HD, reported to the host for delay compensation |
| Bypass | Click-free 20 ms crossfade, delay-compensated |
| Metering | VU with raw input and output needles (RMS) and the curved RAW+IN meter · peak bars with dBFS readouts · RMS readouts · 10-segment GR LEDs with a numeric readout |
| Gain reduction out | VST3 and AAX: compatible hosts, SSL 360° Link with the SSL UC1, the Dynamics LED metering of Pro Tools. Not in LV2 or AUv3 |
| Formats | macOS: AU, VST3, AAX · Windows: VST3, AAX · Linux: VST3, LV2 (.deb and .tar.gz) · iOS: AUv3 and standalone app for iPad and iPhone, iOS 15 or later, from the App Store |
| Presets | 129 factory presets and a browser with folders, favorites, search by name and #tag, and A | B slots |
| Installation and licensing | Installation help, license activation and system requirements: the support pages at pulsarmodular.com |