Floodgate 8 BBD Quick Guide
Pulsar Modular · Zorba Pedals

Floodgate 8 BBD is an analog delay pedal in a plug-in, built around a bucket-brigade delay line, the kind of chip behind classic analog delay pedals. It responds to how hard you play into it, as an analog delay pedal does: quiet notes bloom into the echoes, hard hits are held back. The panel is a dam, and its eight gate lamps light up as the echoes pass.

As usual, we aimed for the stars, happy if we only reached the moon. So we went for the hardest project of all: the infamous analog BBD delay pedal.Ziad Sidawi · Hisham Sidawi, Preface
The panel at its default settings, with audio passing through it
Delay
23.5–1100 msTIME sets one beat from 88.1 to 1100 ms; ECHO divides it, down to 23.5 ms.
ECHO
1/4 → 1/32Seven marked notes, dotted and triplet values among them, and free in between.
STEREO
DUAL · WIDE · PINGFour ways for the two sides to share the echoes, PING L and PING R among them. A mono track plays DUAL.
Latency
0 msNo latency. The pedal reports a 10-second tail, so a host that waits for tails lets the echoes ring out.
Before you start

Four things that work differently

Floodgate 8 BBD behaves like the pedal it is. Four habits from other plug-ins will mislead you, so set them aside first.

1
INPUT drives, TRIM OUT sets the level
INPUT is a drive control, not a volume control. The pedal takes back the level INPUT adds, so a hotter INPUT thickens the sound without making it louder.
2
MIX at D is not your dry track
With the pedal on and MIX at D you still hear the pedal: the dry runs through its saturating path. To hear your original track, use BYPASS.
3
Some knobs need a partner
BLOOM needs FLOOD or loud echoes, FEEDBACK sings only with FLOOD up, and SPEED and STEREO WIDE need some DEPTH. If a control seems to do little, read Knobs together.
4
MATCH is not auto-gain
MATCH sets TRIM OUT once, when you click, so the pedal plays as loud as your dry signal. Play ten seconds first: it reads only while music plays.
Signal path

The pedal, in a fixed order

Your track passes through the pedal in a fixed order. BYPASS takes the whole pedal out of the path.

INPUT
OVERLOAD
Sets how hard the track drives the pedal. The OVERLOAD lamp shows when it drives hard.
▸
Time TIME · ECHO · SYNC · TAP
When the echoes fall: TIME sets one beat, ECHO the note value; SYNC and TAP set TIME to the music.
Repeats HPF · MODERN · FEEDBACK · BLOOM · FLOOD
HPF cuts the low end that enters the echoes, and MODERN keeps the BBD from adding a sub rumble of its own. FEEDBACK, BLOOM and FLOOD shape the repeats.
Warble and tone DEPTH · SPEED · FOLLOW
DEPTH and SPEED make the echoes warble. FOLLOW lets short echoes sound brighter.
▸
MIX
D · FULL · W
Blends the echoes with the dry signal.
▸
TRIM OUT
MATCH
Sets the final level. MATCH sets it for you.
BYPASStakes the pedal out of the signal path: you hear your dry track untouched. With MIX at D you still hear the pedal, because the dry runs through its saturating path, so compare with BYPASS, not with MIX at D.
Mono and stereo
Floodgate 8 BBD runs on mono and stereo tracks. On a stereo track the STEREO bar sets how the two sides share the echoes. On a mono track the pedal plays mono and the bar stays on DUAL.
Mono → Stereo
Some DAWs, such as Logic, let you insert a plug-in on a mono track as Mono → Stereo. Floodgate then turns the mono track into stereo, and WIDE and the PING modes work. On Linux the LV2 is stereo only.
Good to know
Surround and immersive buses are not supported. The pedal adds no latency, and offline bounces are repeatable, sample for sample.
Five-minute walk

Seven steps to know the pedal

1
Put it on a track with space in it
A guitar, keys, a vocal or a snare.
2
Hear it against your dry track
Click the BYPASS footswitch twice while the music plays: once to hear your dry track, once to bring the pedal back. This is the pedal at its default setting: a 375 ms delay, FEEDBACK at 30 %, MIX at noon.
3
Set the time
Click the TAP footswitch four times in time with the track: the fourth tap sets TIME. Or click SYNC, above TIME, to follow the song tempo.
4
Pick a note
Click a note on ECHO (try 1/8 dot): the echoes now fall on that note of the TIME beat. Switch FOLLOW on in the top bar: the shorter the delay, the brighter the echoes.
5
Drive it
Push INPUT up until the OVERLOAD lamp flickers amber on the loudest notes. The track thickens as it drives the pedal.
6
Open the floodgates
Raise FEEDBACK to about 60 % for more repeats. Then raise FLOOD and BLOOM together for the dense, gritty texture.
7
Warble, then flush
Raise DEPTH to hear the echoes warble. Hold FLUSH to empty the delay.
TipIf a change makes the pedal louder or softer than your dry track, click MATCH after ten seconds of playing. It sets TRIM OUT so you compare sound, not level.
Interactive panel

Every control, one click away

Hover for a short note, click for the whole card. 32 spots.
Click a controlIts card opens beside it. The buttons list every spot in panel order, for touch and keyboard; Esc closes the card.
A fresh insert (the Default preset) with a guitar playing through it: OVERLOAD amber on a loud note, the TAP lamp on its beat, the gates lit by the echoes and the BYPASS lamp lit, so the pedal is in the path.

The gates

Eight gate lamps run along the dam in the lower middle of the panel. They light up as the echo travels along the delay line; gate 8 is the echo leaving. The glow follows the level of the echo, so a loud echo lights the gates more strongly. On a flush they blink twice and go dark, and while the pedal is bypassed they rest dark, as the OVERLOAD lamp does. The gates are lamps, not controls.

The gates, lit while echoes travel along the delay line.

The help strip

The band at the bottom of the window explains what is under the pointer: a knob, a button, a lamp or a footswitch. It is on by default. With the pointer over no control it reads “FLOODGATE 8. Hover over a control for help.”, or “FLOODGATE 8 IS IN BYPASS.” while the pedal is bypassed.

The help strip, with nothing under the pointer.

For BYPASS, SYNC, HISS, TRAILS, FOLLOW and MODERN, the text says what you hear now and what a click changes. ECHO and FEEDBACK read live while you turn them, and for one second after: ECHO shows the delay it plays, FEEDBACK says what the repeats do at that setting.

The “?” icon in the top bar, the Tooltip row of the menu or a click on the band itself switches the strip on or off. The switch belongs to the computer: it is shared by every Floodgate 8 BBD on it, kept between sessions, and never stored in a session or a preset. Preset and A/B messages appear in the band even when the strip is off; license notices appear across the top of the panel.

Reference

Controls, ranges and defaults

The controls as printed on the panel. The default is what a fresh insert gives you: the Default preset.

ControlRangeWhat it does
Drive and level
INPUT−18 dB to +18 dB, in steps of 0.1 dBDefault:0 dBHow hard the track drives the pedal. A drive control: the pedal takes back the level it adds.
MIX0 to 100 %Default:50 %, at noonBlends the echoes with the dry, from D (dry) to W (wet). FULL, at 80 %, puts the echoes at their full level.
TRIM OUT−24 dB to +24 dB, in steps of 0.01 dBDefault:0 dBThe output level of the pedal, without changing its sound. MATCH sets it for you.
BYPASSon or offDefault:offOn takes the pedal out of the signal path. The red lamp is lit while the pedal is in the path.
Time
TIME88.1 ms to 1100 msDefault:375 msThe delay for one beat, a quarter note. Dimmed while SYNC is on.
ECHO1/4 to 1/32: seven marked notes, free in betweenDefault:1/4The note value of the echoes against the TIME beat. The delay never goes below 23.5 ms.
SYNCon or offDefault:offThe song tempo sets the beat; ECHO still picks the note value.
Repeats
FEEDBACK0 to 100 %Default:30 %How many repeats you hear, from a single echo to repeats that hold their level at the top.
BLOOM0 to 100 %Default:0 %Drives the repeats harder: denser and grittier, with soft notes echoing louder.
FLOOD0 to 100 %Default:0 %The repeats swell and thicken, with a faint noise of their own. With FEEDBACK high the pedal sings on its own.
HPF0 (off) to 500 Hz, in steps of 1 HzDefault:0 (off)Cuts the low end of what enters the echoes, once. Your dry signal is never touched.
MODERNon or offDefault:offKeeps the BBD from adding a low rumble of its own under the echoes. Off is the original BBD sound.
Warble
DEPTH0 to 100 %Default:0 %How far the pitch of the echoes swings. At 0 the echoes hold steady.
SPEED0 to 100 %, which is 0.1 Hz to 5.9 HzDefault:50 %, about 2.07 HzHow fast the echoes warble, from a slow drift to a quick flutter. It needs some DEPTH.
Top bar
STEREODUAL, WIDE, PING L, PING RDefault:DUALHow the two sides share the echoes. It needs a stereo output.
HISSon or offDefault:onThe quiet hiss of the delay circuit under the echoes.
TRAILSon or offDefault:onOn, the echoes ring out after you bypass. Off, bypass cuts them.
FOLLOWon or offDefault:offOn, the shorter the delay, the brighter the echoes. Off, the echo filters stay where they are.
TipDrag a knob up or down to turn it. Point at a knob to see its value under it, and click that value to type a new one. Double-click a knob, or Option-click it on the Mac (Alt-click on Windows and Linux), to return it to its default. The rest is in Mouse and keys.
TIME · ECHO · SYNC · TAP

When the echoes fall

TIME and ECHO decide when the echoes fall. SYNC and TAP are two ways to set TIME to the music.

SYNC on: its lamp is lit, TIME is dimmed, and the readout beside its name shows the tempo and the beat. Right of it, the ECHO ring: seven notes, each with its name beside its tick.

TIME

TIME is the first knob of the top row, left of ECHO. It sets the delay for one beat, a quarter note, from 88.1 ms to 1100 ms; the default is 375 ms and the readout shows milliseconds. With ECHO on 1/4, the delay is TIME itself.

ECHO

ECHO picks the note value of the echoes against the TIME beat; the default is 1/4. Seven thick ticks around the knob mark the notes, and the panel prints each note’s name beside its tick. Click a tick, or the name beside it, to set ECHO exactly on that note: the readout then names the note. Between the ticks the knob turns freely, and the readout shows the ratio instead, for example “x 0.62”.

The delay never goes below 23.5 ms. With a short TIME and a short note, it stops there.

TickNoteDelay
7 o’clock1/4the whole TIME beat
8 o’clock1/8 dotthree quarters of it
10 o’clock1/8half
12 o’clock1/8 tripa third
1 o’clock1/16a quarter
3 o’clock1/16 tripa sixth
5 o’clock1/32an eighth

SYNC

SYNC is the button in the jack strip along the top edge of the pedal, above TIME. It is off by default, and its lamp is lit while it is on. With SYNC on, the song tempo sets the delay, one beat per quarter note, and ECHO picks the note value. TIME is dimmed and has no effect; it keeps its setting for when you switch SYNC off. A readout beside the word TIME shows the tempo and the beat, for example “120 BPM - 500 ms”.

The beat stays within TIME’s range: below 54.5 BPM it is held at 1100 ms. If the host sends no tempo, SYNC has nothing to follow and the pedal plays TIME, which still shows dimmed.

TAP

Count in
TAP is the footswitch at the bottom left. Taps 1 to 3 only count in; the fourth tap sets TIME.
Refine
Every tap after that refines it, from the last eight gaps. A change under 1 % is ignored, so the delay does not wobble on a steady tap.
Start again
Stop for longer than two beats and the next tap starts a new count. Before your first count has set TIME, that pause is 2 seconds.

TAP turns the TIME knob, so the host records the change like a hand-turn. With SYNC on, TAP still sets TIME, but the tempo wins until you switch SYNC off. The green lamp by TAP blinks at the beat rate: the TIME beat, or the song tempo with SYNC on.

Repeats

How many, how hard, how long

FEEDBACK, BLOOM and FLOOD shape the repeats: how many there are, how hard they are driven, and whether they run on by themselves. HPF and MODERN keep their low end clear. The FLUSH footswitch empties them. The three knobs sit in the REPEATS group, below TIME and ECHO.

FEEDBACK
0 to 100 %, default 30 %. How many repeats you hear, from a single echo to repeats that hold their level at the top. They grow into a sing only with FLOOD up.
BLOOM
0 to 100 %, default 0 %. Drives the repeats harder: denser and grittier, with soft notes echoing louder. On its own, with FLOOD at 0 and MIX at noon, it is subtle. It shines with FLOOD up or with loud echoes.
FLOOD
0 to 100 %, default 0 %. Opens the floodgates: the repeats swell and thicken, with a faint noise of their own. With FEEDBACK high the pedal sings on its own, even with nothing playing.

HPF and MODERN: a clear low end

The jack strip along the top edge of the pedal: MODERN and SYNC on, HPF at 130 Hz, TRIM at −6.00 dB, and MATCH showing a gap with its red dot.
HPF
The bar labelled HPF in the jack strip, from 0 (off) to 500 Hz; 100 Hz is near the middle. Echoes stack up, and so does their low end: with long repeats, FLOOD or BLOOM up, the bass of the first repeats can pile up under your track and muddy it. HPF cuts the low end of what enters the echoes, once, and each repeat keeps the cut. How dark the repeats get depends on FOLLOW. Your dry signal is never touched.
HPF does not reach the sub rumble the BBD makes by itself; MODERN takes that away. To hear what HPF does, point at the bar and hold Cmd and Option on the Mac (Ctrl and Alt on Windows and Linux): the echoes play without the cut until you let go, and the bar grays out. The setting itself does not change.
MODERN
The switch at the left end of the jack strip, off by default: off is the original BBD sound. As the echoes go round, the BBD adds a low rumble of its own under them. It is part of the classic sound, and it grows with FLOOD up. MODERN keeps the BBD from adding it. The echo body, the mids and the level stay as they are, and your dry signal is never touched.
MODERN matters most with FLOOD and FEEDBACK up, on chords, pads and chorus. On bass and drums it changes little. It switches smoothly, with no click.
TipEchoes muddying the low end? Turn MODERN on first. If the low end still needs room, raise HPF, from about 60 Hz up. Both leave the dry alone.

FLUSH

  • FLUSH is the footswitch under FLOOD. Hold it to empty the delay: the echoes fade out and stay silent while you hold, and your dry signal still plays.
  • When you let go, the repeats build up again from what you play next. A singing loop builds up again by itself (see Knobs together).
  • A flush always runs to its end, even if you let go early. The green lamp by FLUSH is lit while you hold it, and the eight gate lamps blink twice and go dark.
  • With MIX at W there is no dry signal, so the output is silent until new echoes build. FLUSH is a momentary switch: it is never stored in a preset or a session.
Warble and the top bar

Wobble, width and tone

DEPTH and SPEED, in the WARBLE group at the right, give the echoes a wobble in pitch. HISS, TRAILS, FOLLOW and the STEREO bar sit in the top bar.

DEPTH
0 to 100 %, default 0 %. How far the pitch of the echoes swings: a little adds shimmer, a lot a deep warble. At 0 the echoes hold steady, so WARBLE is off until you turn DEPTH up. DEPTH is a share of the delay, so the same setting wobbles more at long delays than at short ones. On a stereo track, STEREO WIDE spreads the warble across the two sides.
SPEED
0 to 100 %, default 50 %. The readout shows Hz: 0.1 Hz at 0 %, about 2.07 Hz at the default and about 5.9 Hz at 100 %. SPEED sets how fast the echoes warble, from a slow drift to a quick flutter. It needs some DEPTH to be heard.

STEREO

The top bar: the preset bar with its two arrows, A/B and its copy icon, HISS and TRAILS (both on), FOLLOW, the STEREO bar on DUAL, the “?” icon and the menu button.

STEREO is a bar of four segments. Click a segment to choose the mode; the default is DUAL.

ModeWhat it does
DUALEach side echoes itself, left on the left and right on the right, both warbling in step. A mono source stays in the center.
WIDELike DUAL, but the right side warbles a quarter cycle apart from the left, so the echoes spread out. Needs some DEPTH to be heard.
PING LBoth sides feed one delay and the echoes bounce side to side. The first repeat is on the left.
PING RThe same, with the first repeat on the right.
TipUse PING L on one track and PING R on another to keep the mix centered.

STEREO needs a stereo output. On a mono track or bus, WIDE, PING L and PING R are dimmed: the pedal plays DUAL, and a click on a dimmed segment blinks it twice. The mode you chose is kept, so it comes back when the pedal sits on a stereo track or bus. With the pedal inserted as Mono → Stereo, all four modes work.

HISS · TRAILS · FOLLOW

HISS
On by default. Adds the quiet hiss of the delay circuit under the echoes. Off removes it.
TRAILS
On by default: the echoes ring out after you bypass. With TRAILS off, bypass cuts them, but the loop runs on unheard: repeats that hold or sing are still there when you switch the pedal in again, while shorter ones have faded by then. Only FLUSH empties the loop.
FOLLOW
Off by default: the echo filters stay where they are at every delay time. On, the tone follows the delay: the shorter the delay, the brighter the echoes, and at the longest delay, 1100 ms, on and off sound the same. FOLLOW reads the delay you hear (TIME and ECHO, or the song beat and ECHO with SYNC on); DEPTH and SPEED do not move it. The switch glides over 100 ms, so it does not click.
Drive and level

From INPUT to TRIM OUT

INPUT sets how hard your track drives the pedal and the OVERLOAD lamp shows when it drives hard. MIX blends the echoes with your dry signal, TRIM OUT sets the level of the pedal, MATCH sets that level for you, and BYPASS takes the pedal out.

INPUT and the OVERLOAD lamp

INPUT is the knob on the left, from −18 dB to +18 dB in steps of 0.1 dB; the default is 0 dB. Track peaks around −12 dBFS with INPUT at 0 dB give the reference response. Hotter signals thicken the dry into a warm analog saturation, and the echoes get denser and more compressed. For a clean dry, turn INPUT down until the OVERLOAD lamp stays dark.

The lamp sits above INPUT and reads the peak of your track after INPUT. Each color holds for 300 ms, so a short peak stays visible, and red wins over amber; the lamp is dark while the pedal is bypassed. Turn INPUT up until it flickers amber on the loudest notes. If it stays red, turn INPUT down.

LampMeaning
DarkThe peak is below −6 dBFS.
AmberFrom −6 dBFS. The input starts to saturate, a thick warm edge.
RedFrom −2 dBFS. The input hits the pedal’s ceiling.

MIX

MIX is the last knob of the top row, from 0 to 100 %; the default is 50 %, at noon. The ends are printed D, for dry, at the left, and W, for wet, at the right, and FULL is printed beside the knob: click FULL to set MIX right on it. At D you still hear the pedal, not the original track.

D to FULL
The dry stays at full level and the echoes rise. Noon is an even balance for most playing: the echoes sit at about the level of your notes.
FULL
At 80 %. The echoes are at their full level, louder than soft playing, as an analog delay’s echoes bloom.
Past FULL
The dry fades out, down to echoes only at W. Use this on an aux send.

TRIM OUT

TRIM OUT is the bar labelled TRIM in the jack strip, from −24 dB to +24 dB in steps of 0.01 dB; the default is 0 dB. It sets the output level of the pedal without changing its sound. Drag it, with Ctrl held for fine steps; double-click it to type a value; Option-click on the Mac, or Alt-click on Windows and Linux, returns it to 0 dB.

BYPASS skips TRIM OUT for the dry signal, so it keeps its own level; echoes that ring out after bypass still follow TRIM OUT. When you switch the pedal on, the first echo takes one delay time to arrive: TRIM OUT waits at 0 dB until then, then glides to its setting, so the dry does not dip when the pedal comes in.

MATCH

MATCH is the push button at the right end of the jack strip. It sets TRIM OUT so the pedal plays as loud as your dry signal, by perceived loudness.

1 · Play
Play the music for ten seconds with the pedal on. The reading settles over that time, so it follows the phrase, not each note.
2 · Click
Click MATCH. Its outline flashes amber twice.
3 · Check
Switch BYPASS on, then off again. The loudness holds.

A red dot on MATCH shows a gap of 1 dB or more between your dry signal and the pedal. The larger the gap, the brighter the dot, up to full at 6 dB, and it breathes slowly. It goes out when the gap falls under 0.7 dB, in bypass, and when the music stops. MATCH reads only while music plays, and TRIM OUT stops at ±24 dB.

NoteMATCH is not auto-gain. It sets the level once, when you click.

BYPASS

BYPASS is the footswitch at the bottom right. BYPASS on takes the pedal out of the signal path: you hear your dry track untouched and can compare. BYPASS off puts the pedal back in; the red lamp by BYPASS is lit while the pedal is in the path. BYPASS follows the bypass of your DAW’s insert, and the DAW’s follows it. With TRAILS on, the echoes ring out after you bypass. A preset applies the BYPASS it stores; the A/B slots never hold it.

Gain staging

In a chain
A hotter signal upstream drives the pedal harder. Set the gain upstream first, then INPUT. Set INPUT with the whole mix playing, not with the track soloed.
Into the next device
Set the level that leaves the pedal with TRIM OUT. MATCH holds the loudness, not the peaks: a denser signal can peak differently at the next device.
On a send
On an aux send, the send level and INPUT together set how hard each track drives the pedal.
TipSet the drive by the OVERLOAD lamp. Set the level by TRIM OUT and the meter after the pedal.
Partners

How the knobs work together

Some controls show little on their own. They need a partner.

BLOOM + FLOOD
BLOOM on its own, with FLOOD at 0 and MIX at noon, is subtle. FLOOD loosens the pedal’s compression, and that lets BLOOM’s drive through. With FLOOD up, or with the echoes loud (MIX from FULL up to W), BLOOM gives the dense, gritty texture.
FLUSH on a singing loop
FLUSH empties the delay, but a loop that is singing builds up again by itself. At short delays that happens within a fraction of a second: about seven trips around the loop, 0.17 s at the shortest delay of 23.5 ms. To keep it down, lower FLOOD or FEEDBACK as well.
TryFEEDBACK at 50 %, FLOOD at 0, MIX at noon, and sweep BLOOM from 0 to 100 %. Set MIX to FULL and sweep again. Then set FLOOD to 40 % and sweep once more.
TryTIME at its shortest, ECHO on 1/32, FEEDBACK at the top, FLOOD up. Hold FLUSH, let go, and listen to the sing return.

When a control seems to do nothing

ControlSeems to do nothing whenBecause
BLOOMFLOOD is 0 and MIX is at noonBLOOM needs FLOOD or loud echoes.
FEEDBACK at the topFLOOD is 0The repeats hold but do not sing.
SPEEDDEPTH is 0There is no warble to speed up.
STEREO WIDEDEPTH is 0There is no warble to spread.
STEREOThe output is monoWIDE and the PINGs are dimmed; the pedal plays DUAL.
ECHO, short notesTIME is shortThe delay stops at 23.5 ms.
TIMESYNC is onThe song tempo sets the delay.
FOLLOWThe delay is 1100 msAt the longest delay, on and off sound the same.
MIX at DYou expect your original trackThe dry runs through the pedal; use BYPASS.
INPUTYou listen for levelINPUT drives, TRIM OUT sets the level.
TRIM OUTBYPASS is onBypass skips it for the dry signal.
In practice

Seven recipes

Each recipe starts from the Default preset. Change only what is listed.

1Slapback
SettingsTIME at its shortest, ECHO on 1/4, FEEDBACK at 10 %, MIX at noon.
You hearA single short echo close behind each note.
2Dotted eighth in time
SettingsSYNC on, ECHO on 1/8 dot, FEEDBACK at 35 %, MIX at noon.
You hearEchoes that fall on the dotted eighth of the song tempo.
3Dense, gritty echoes
SettingsFEEDBACK at 50 %, FLOOD at 40 %, BLOOM at 70 %, MIX at FULL.
You hearThe dense, gritty texture that BLOOM gives with FLOOD up and the echoes loud.
4A singing loop
SettingsFEEDBACK at the top, FLOOD at 60 %, MIX at noon. Play a note and stop.
You hearThe pedal singing on its own after the note ends. Hold FLUSH to empty it, and let go to hear it build again.
5Pitch wobble
SettingsDEPTH at 30 %, SPEED at the default, FEEDBACK at 40 %.
You hearThe echoes shimmer in pitch while the dry stays steady.
6Echoes only, on a send
SettingsOn an aux send, MIX at W. Set TIME, ECHO and FEEDBACK as you like.
You hearOnly the echoes. Set how much of each track reaches them with the send level.
7A ping-pong pair
SettingsThe same TIME and ECHO on two stereo tracks. STEREO on PING L on one track, PING R on the other.
You hearEchoes bouncing side to side, the mix still centered.
A/B and presets

Two slots, one bank

Presets are files on disk. The A/B slots, in the top bar, hold two settings to compare.

The A/B slots

Click A/B to switch slots. The lit letter is the slot you hear, and the slot you leave keeps its settings. The copy icon, right of A/B, copies the slot you hear over the other, with no undo. A slot holds the knobs and buttons, never BYPASS, so a switch never bypasses the pedal. Loading a preset or reopening a session fills both slots with the same sound. Neither the session nor a preset saves the slots.

The preset bar

The preset name sits at the left of the top bar, between two arrows. Click the name to open the browser. The arrows step through the whole bank: from Default into the first folder, then folder by folder in the order of the folder list. At either end they wrap around. With Favorites or Search open, they step through that list.

●Default
An amber dot by the name: a control has moved since the last load or save. BYPASS and FLUSH do not count.
INIT
Nothing is loaded.
Blues Lead (deleted)
The name in italic, with “(deleted)”: the loaded preset’s file was moved or deleted outside Floodgate 8 BBD.

The browser

The left list holds All / root (the whole bank), your folders, and the Favorites and Search views; the right list holds the presets. Hover over a part of the browser below for a note. The view is the User Guide’s: the Guitar folder open, Blues Lead selected, its tags and description in the line under the lists. The browser opens again where you left it.

TAGS
★
★  Favorites (0)
⌕  Search (type above)
All / root
Bass
Drums
Drum Bus
Kick
Percussion
Snare & Clap
Toms
Experimental
Guitar
Sends
Synths
Bass Sequences
Character
Chords & Pads
Chorus
Leads
Ping Pong
Plucks & Arps
Vocals
☆Almost Dry
☆Ambient Swells
☆Blues Lead
☆Clean Eighths
☆Clean Sixteenths
☆Dotted Arpeggio
☆Drifting Double
☆Driven Lead
☆Fast Vibrato
☆Quarter-Note Space
guitar, lead, insert, subtle, free time, few repeats  ·  Insert on blues lead with bends. A short tail of 280 ms repeats rings into the rests between phrases. If the tail gets in the way, lower FEEDBACK first. For more echo, raise MIX.
NEW FOLDER
SAVE
SAVE AS
RENAME
DELETE
CLOSE

Where the files live

All copies of Floodgate 8 BBD on the computer share one preset folder; on Linux, each user account has its own. Open Preset Folder, in the menu, opens it. Each preset is one .FGBBDPreset file named after the preset, and renames and moves in Finder or Explorer show up in the browser. There is no import or export: copy preset files into the folder or out of it. Preset files travel between macOS, Windows and Linux. To back up, copy the folder.

Windows
C:\Users\Public\Documents\Pulsar Modular\Floodgate 8 BBD\Presets
macOS
/Users/Shared/Pulsar Modular/Floodgate 8 BBD/Presets
Linux
~/.local/share/Pulsar Modular/Floodgate 8 BBD/Presets

What a preset stores

Stores
Every control on the panel, BYPASS included, and the preset’s name, description and tags. A loaded preset applies its BYPASS; the factory presets are saved with BYPASS off.
Never stores
FLUSH, the A/B slots and the help strip switch. The window size is stored only in the Default.

The factory presets and the Default

The 79 factory presets are sorted into seven folders: Bass, Drums, Experimental, Guitar, Sends, Synths and Vocals. Drums has its own folders for the drum bus, kick, percussion, snare and clap, and toms. Synths has folders for bass sequences, character, chords and pads, chorus, leads, ping pong, and plucks and arps. Each preset’s tags and description say what it is for and where to start.

The preset named Default loads on every new insert. To change it, set the pedal as you want it, right-click in the browser and choose “Save these settings as the startup default”. Or load Default, change it and click SAVE. An update never replaces the Default: the installer adds it only when the preset folder has none, so a Default you saved stays yours.

The 79 factory presets by folder
Bass9
  • Bass Buzz
  • Bass Chorus
  • Bass Interlock
  • Bass Thickener
  • Dub Response
  • Fretless Space
  • Muted Groove
  • Picked Bass Slap
  • Tight Fingerstyle
Drums › Drum Bus2
  • Broken Beat Echo
  • Kit Short Reflection
Drums › Kick1
  • Kick Answer
Drums › Percussion3
  • Conga Triplet Roll
  • Cowbell Slapback
  • Rim Dotted Answer
Drums › Snare & Clap5
  • Snare Backbeat Echo
  • Snare Dub Throw
  • Snare Sixteenth Roll
  • Snare Small Space
  • Snare Vintage Slap
Drums › Toms2
  • Tom Afterglow
  • Tom Triplet Roll
Experimental5
  • Bloom Wash
  • Latching Drone
  • Resonant Comb
  • Runaway Flood
  • Slow Metallic Sweep
Guitar13
  • Almost Dry
  • Ambient Swells
  • Blues Lead
  • Clean Eighths
  • Clean Sixteenths
  • Dotted Arpeggio
  • Drifting Double
  • Driven Lead
  • Fast Vibrato
  • Quarter-Note Space
  • Rockabilly Slap
  • Tight Double
  • Wide Guitar Chorus
Sends3
  • Last Word Send
  • Snare Backbeat Echo Send
  • Snare Dub Throw Send
Synths › Bass Sequences1
  • Bass Sequence Space
Synths › Character1
  • BBD Character
Synths › Chords & Pads4
  • Ambient Bed
  • Chord Echo
  • Pad Drift
  • Stab Flutter
Synths › Chorus5
  • Animated Strings
  • Dreamy BBD Chorus
  • Lead Doubler
  • Soft Poly Chorus
  • Wide Pad Ensemble
Synths › Leads2
  • Mono Lead Slap
  • Singing Lead
Synths › Ping Pong6
  • Alternating Plucks
  • Ambient Cross-Echo
  • Dotted Stereo Sequence
  • Sixteenth Bounce L
  • Sixteenth Bounce R
  • Wide Chord Replies
Synths › Plucks & Arps6
  • Arp Sixteenths
  • Dotted Interlock
  • Pluck Answer
  • Pluck Triplet Roll
  • Sequence Glue
  • Triplet Motion
Vocals11
  • Background Haze
  • Close Vocal
  • Dotted Motion
  • Dream Tail
  • Last Word
  • Quarter Space
  • Tight Eighth
  • Vintage Rock Slap
  • Vocal Double
  • Vocal Widener
  • Warm Slap
Mouse and keys

Hands on the panel

DoWhat happens
Drag a knob up or downTurns it.
Point at a knobIts value shows under it. Click that value to type a new one.
Double-click a knob, or Option-click it (Alt-click on Windows and Linux)Returns it to its default.
Click the HPF or TRIM OUT barA click on a bar always drags it. Double-click the bar to type a value; Option-click (Alt-click) returns it to its default.
Hold Ctrl while you dragFine steps, on any control.
Point at HPF and hold Cmd and Option (Ctrl and Alt on Windows and Linux)The echoes play without the cut until you let go, and the bar grays out. The setting itself does not change.
Click an ECHO tick or its name, or FULLSets ECHO exactly on that note, or MIX right on FULL.
Click TAP four timesThe fourth tap sets TIME; every tap after that refines it.
Hold FLUSHEmpties the delay. The echoes stay silent while you hold.
Click the help strip, or the “?” iconSwitches the help strip on or off.
Drag the corner of the windowResizes it. The aspect ratio is locked.
Installation and license

Install, then activate

Install the format your DAW uses; the pedal is the same in each. The installer offers the formats, the presets and the user guides as separate items. On Linux, one package installs both formats with the presets and the guides.

FormatPlatformInstalled at
VST3macOS/Library/Audio/Plug-Ins/VST3/Pulsar Modular/Floodgate 8 BBD.vst3
VST3WindowsC:\Program Files\Common Files\VST3\Pulsar Modular\Floodgate 8 BBD.vst3
AUmacOS/Library/Audio/Plug-Ins/Components/Floodgate 8 BBD.component
AAXmacOS/Library/Application Support/Avid/Audio/Plug-Ins/Pulsar Modular/Floodgate 8 BBD.aaxplugin
AAXWindowsC:\Program Files\Common Files\Avid\Audio\Plug-Ins\Pulsar Modular\Floodgate 8 BBD.aaxplugin
VST3Linux~/.vst3/Floodgate 8 BBD.vst3
LV2Linux/usr/lib/lv2/Floodgate 8 BBD.lv2 (.deb) or ~/.lv2/Floodgate 8 BBD.lv2 (.tar.gz)

Where presets and guides live

macOS
/Users/Shared/Pulsar Modular/Floodgate 8 BBD/Presets/Users/Shared/Pulsar Modular/Floodgate 8 BBD/User Guides
Windows
C:\Users\Public\Documents\Pulsar Modular\Floodgate 8 BBD\PresetsC:\Users\Public\Documents\Pulsar Modular\Floodgate 8 BBD\User Guides
Linux
For each user account.
~/.local/share/Pulsar Modular/Floodgate 8 BBD/Presets~/.local/share/Pulsar Modular/Floodgate 8 BBD/User Guides
A fresh insert
A new insert loads the Default preset. Its settings are the defaults in the controls table.

License

Without an activated license, Floodgate 8 BBD plays a soft noise instead of your audio, and the license window opens by itself (it comes back if you close it). Open it from the menu, License Status. Paste your license key and click Activate: the status line turns green and your audio returns at once, with no restart.

ButtonDoes
ActivateActivates this computer with the key.
DeactivateFrees this computer’s seat.
RefreshChecks the license now.
AccountOpens your account page on the web, where you manage your computers.

A demo license shows the days left in the window. The license renews online by itself. If it cannot reach the server, the plug-in keeps playing until the date shown in a line across the top of the panel: “LICENSE CHECK OVERDUE - plays until ...”. Connect to the internet and click Refresh.

The same line shows the other license states: LICENSE LAPSED, HARDWARE CHANGED while the license moves to new hardware, and THIS MACHINE HAS NO USABLE DEVICE ID. Each ends with “Click for Refresh or Account.” A click on the line opens the license window.

Linux

Floodgate 8 BBD on Linux

The same plug-in as on macOS and Windows, with the same sound, controls and presets. It runs as VST3 and LV2 on 64-bit Intel and AMD computers with glibc 2.34 or later: Ubuntu 22.04, Debian 12, Fedora 35, Linux Mint 21 and their later versions, and current Arch-based distributions. This command shows the glibc version on your computer. The pedal is tested in Ardour 9, Mixbus 11 and REAPER 7.

getconf GNU_LIBC_VERSION
.deb packageUbuntu, Debian, Linux Mint, Pop!_OS. In its folder, run sudo apt install ./floodgate-8-bbd_<version>_amd64.deb. It installs the LV2 for the whole computer, links the VST3 into each user account’s ~/.vst3, and gives each account the factory presets and the guides. An account created later is set up the same way with sudo dpkg-reconfigure floodgate-8-bbd.
.tar.gz archiveAny distribution, no administrator rights: unpack it and run ./install.sh in its folder. It installs into your own ~/.vst3, ~/.lv2 and ~/.local/share.
One of them, never bothTwo copies of the LV2 make Ardour and Mixbus crash, so install.sh refuses to run while the .deb is installed, and the .deb warns when it finds a copy from the archive. After installing, rescan plug-ins in REAPER or Bitwig Studio; Ardour and Mixbus scan at start-up, so restart them.
Factory presetsAs on macOS and Windows, every install or update restores the factory presets, deleted ones included, but never replaces the Default. To keep changes to a factory preset, save it under a new name.
LicenseOne activation covers every host and both formats for your user account on this computer. The license is tied to this installation of Linux: reinstalling or cloning the system counts as a new computer, so click Deactivate before you reinstall. If the pedal says it is unlicensed on a computer where you activated it, contact us instead of activating again: activations are limited.
Which formatREAPER: the VST3 (REAPER cannot automate the LV2’s parameters). Ardour and Mixbus: both formats work. Bitwig Studio: the VST3 (Bitwig has no LV2 host).
Mono and stereoThe VST3 runs on mono and stereo tracks. The LV2 is stereo only, so use the VST3 on a mono track.
BypassIn the VST3, the host’s bypass and the BYPASS footswitch are one switch. In the LV2, the host’s bypass takes the pedal out of the signal path as the footswitch does, but the footswitch does not follow: its red lamp stays lit.
Parameter valuesHosts show the LV2’s parameters as plain numbers. The VST3 shows them as the panel does: milliseconds, percent, decibels and note values.
Alt-clickReturns a control to its default, as on Windows. A desktop that moves windows with Alt and a drag, such as Xfce, takes that click: double-click a knob instead, or set the key the desktop uses to move windows to Super.
FilesEach user account has its own. Presets: ~/.local/share/Pulsar Modular/Floodgate 8 BBD/Presets. User guides: the User Guides folder next to it; Manuals, in the menu, opens them in your PDF viewer. Settings: ~/.config/Pulsar Modular/Floodgate 8 BBD/Settings. License: ~/.config/Pulsar Modular/Licensing, shared by every Pulsar Modular product on the computer. A preset or folder you delete in the browser goes to the desktop’s trash, and Show in file manager takes the place of Reveal in Finder.
Window sizeDrag the corner of the VST3 window, and the frame of the LV2 window (in REAPER, its corner). If dragging gives the LV2 window another aspect ratio, the panel takes the largest size that fits, centered between black bands. On a HiDPI screen, both formats follow the host’s own interface scale.
Crackles at small buffer sizesThey usually mean that the DAW lacks realtime privileges. Add your account to the audio group (sudo usermod -aG audio $USER), give that group realtime limits (LINUX-NOTES.txt in the download has the command), then log out and back in. On a laptop, also choose the Performance power profile.
Uninstalling

Removing Floodgate 8 BBD

To keep your presets, copy the Floodgate 8 BBD folder first. If you are leaving the computer for good, deactivate the license first. Delete the Pulsar Modular folder too if it is left empty.

Windows
Delete the plug-in files, the Floodgate 8 BBD folder (presets and user guides) and the settings in your user application data under Pulsar Modular\Floodgate 8 BBD.
C:\Program Files\Common Files\VST3\Pulsar Modular\Floodgate 8 BBD.vst3C:\Program Files\Common Files\Avid\Audio\Plug-Ins\Pulsar Modular\Floodgate 8 BBD.aaxpluginC:\Users\Public\Documents\Pulsar Modular\Floodgate 8 BBD
macOS
Delete the plug-in files, the Floodgate 8 BBD folder (presets and user guides) and the settings in your user Library under Application Support/Pulsar Modular/Floodgate 8 BBD.
/Library/Audio/Plug-Ins/Components/Floodgate 8 BBD.component/Library/Audio/Plug-Ins/VST3/Pulsar Modular/Floodgate 8 BBD.vst3/Library/Application Support/Avid/Audio/Plug-Ins/Pulsar Modular/Floodgate 8 BBD.aaxplugin/Users/Shared/Pulsar Modular/Floodgate 8 BBD
Linux
For the .deb:
sudo apt remove floodgate-8-bbd
For the .tar.gz, in the folder you installed from:
./uninstall.sh
Both keep your presets, the guides and your settings. To remove them too, delete the Floodgate 8 BBD folders in ~/.local/share/Pulsar Modular and ~/.config/Pulsar Modular, but keep the Licensing folder: it holds every Pulsar Modular license on the computer.

The settings hold the help strip switch and your favorites.

Specifications

Specifications

FormatsVST3, AU, AAX; VST3 and LV2 on Linux
ChannelsMono in, mono out; mono in, stereo out; stereo in, stereo out. Surround and immersive buses are not supported.
Delay time23.5 ms to 1100 ms (TIME alone covers 88.1 ms to 1100 ms; ECHO reaches the shorter delays)
Latency, tailNo latency; a tail of 10 seconds, as reported to the host
Offline rendersRepeatable, sample for sample
Parameters19, each under its panel name; FLUSH is momentary and never stored
Presets79 factory presets in seven folders, and the Default; one .FGBBDPreset file per preset, the same on macOS, Windows and Linux
Window800 × 545 points by default, from half to twice that size, never past 90 % of the display; the aspect ratio is locked
Linux64-bit Intel and AMD, glibc 2.34 or later
Troubleshooting

Troubleshooting and FAQ

The sound
I hear a soft noise instead of my audio.
Floodgate 8 BBD is not licensed on this computer. Activate it from the menu, License Status.
INPUT does not make it louder.
By design: INPUT drives the pedal and the pedal takes back the level it adds. Use TRIM OUT for level.
The pedal is louder or softer than my dry track.
Play ten seconds and click MATCH.
BLOOM does almost nothing.
Raise FLOOD, or set MIX from FULL up to W.
FEEDBACK at the top does not sing.
The pedal sings only with FLOOD up.
SPEED or WIDE does nothing.
Raise DEPTH.
TIME does not respond.
SYNC is on. The song tempo sets the delay.
Short echoes are brighter than long ones.
FOLLOW is on. Switch it off and the echo filters stay where they are at every delay.
My dry track sounds thicker with MIX at D.
The dry runs through the pedal’s saturating path. Use BYPASS for the original.
The sing comes back right after FLUSH.
At short delays a singing loop builds up again within a fraction of a second. Lower FLOOD or FEEDBACK as well.
PING L, PING R and WIDE are dimmed.
The pedal sits on a mono track or bus. Put it on a stereo track or bus, or insert it as Mono → Stereo where your DAW offers that.
The echoes muddy the low end.
Turn MODERN on: it keeps the BBD from adding its own sub rumble. If the low end still needs room, raise HPF, from about 60 Hz up. Both leave the dry alone.
The panel
The help strip is gone.
It is switched off. Switch it on with the “?” icon.
A Manuals row opens a WARNING window: “File does not exist!”
That guide is not installed. Run the installer with User Guides selected. On Linux, run sudo dpkg-reconfigure floodgate-8-bbd (.deb) or install.sh again (.tar.gz).
Presets and sessions
My preset bypassed the pedal.
A preset stores BYPASS and applies it on load. Save it again with BYPASS off.
Why is FLUSH not in my preset?
FLUSH is a momentary switch: it is never stored in a preset or a session.
Hosts and renders
Surround or immersive tracks?
Not supported.
I want stereo echoes from a mono track.
Put the pedal on a stereo track or bus, or insert it as Mono → Stereo where your DAW offers that.
Does Floodgate 8 BBD add latency?
No.
The echoes cut off when I bypass.
TRAILS is off. Switch it on and the echoes ring out.